3270316 Phoenix Contact Terminal Blocks

Product Details

• Test directions
  X-, Y- and Z-axis (pos. and neg.)
• Number of shocks per direction
  3
• Static insulating material application in cold
  -60 °C
• Surface flammability NFPA 130 (ASTM E 162)
  passed
• Fire protection for rail vehicles (DIN EN 45545-2) R23
  HL 1 - HL 3
• Fire protection for rail vehicles (DIN EN 45545-2) R26
  HL 1 - HL 3
• Width
  34.4 mm
• Number of positions
  32
• Insulating material
  PA
• Insulating material group
  I
• Maximum load current
  24 A (in case of a 2.5 mm² conductor cross section, the maximum load current must not be exceeded by the total current of all connected conductors.)
• Maximum power dissipation for nominal condition
  0.56 W (the value is based on one connection block and is multiplied according to the pin assignment)
• Back of the hand protection
  guaranteed
• Power frequency withstand voltage setpoint
  1.89 kV
• Result of power-frequency withstand voltage test
  Test passed
• Bending test conductor cross section/weight
  0.14 mm² / 0.2 kg
• Result of temperature-rise test
  Test passed
• Result of voltage-drop test
  Test passed
• Short circuit stability result
  Test passed
• Oscillation, broadband noise test result
  Test passed
Test spectrum
Service life test category 1, class B, body mounted
Acceleration
5g
Shock test result
Test passed
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Stripping length
8 mm ... 10 mm
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.34 mm²
Connection cross sections directly pluggable
0.34 mm² 2.5 mm² 20 14
Ambient temperature (assembly)
-5 °C ... 70 °C
Length
111 mm
Connection in acc. with standard
IEC 60947-7-1
Conductor cross section AWG min.
26
Conductor cross section flexible max.
1.5 mm²
Max. AWG conductor cross section, flexible
14
Conductor cross section flexible, with ferrule with plastic sleeve max.
1.5 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 10.0.1
27141120
ECLASS 5.0
27141100
ECLASS 6.0
27141100
UNSPSC 20.0
39121410
Number of levels
1
Nominal cross section
1.5 mm²
Color of connection elements
gray/white
Rated surge voltage
6 kV
Nominal current IN
17.5 A
Open side panel
No
Finger protection
guaranteed
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Bending test rotation speed
10 rpm
Tensile test result
Test passed
Note
The max. load current must not be exceeded by the total current of all connected conductors.
Number of connections
128
Color
gray
Flammability rating according to UL 94
V0
Degree of pollution
3
Overvoltage category
III
Nominal voltage UN
500 V
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Result of surge voltage test
Test passed
Result of flexion and pull-out test
Test passed
Bending test turns
135
Result of tight fit on support
Test passed
Tight fit on carrier
NS 35
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Setpoint
1 N
Conductor cross section short circuit testing
2.5 mm²
Short-time current
0.3 kA
Result of thermal test
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Result of aging test
Test passed
Ageing test for screwless modular terminal block temperature cycles
192
Test frequency
f1 = 5 Hz to f2 = 150 Hz
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
ASD level
0.964 (m/s2)2/Hz
Test duration per axis
5 h
Shock form
Half-sine
Shock duration
30 ms
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Calorimetric heat release NFPA 130 (ASTM E 1354)
27,5 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Connection method
Push-in connection
Conductor cross section solid min.
0.34 mm²
Min. AWG conductor cross section, flexible
26
Conductor cross section AWG max.
14
Conductor cross section flexible, with ferrule without plastic sleeve max.
1.5 mm²
Internal cylindrical gage
A1
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 11.0
27141120
ECLASS 5.1
27141100
UNSPSC 18.0
39121410
UNSPSC 21.0
39121410
Height
30 mm
Conductor cross section solid max.
2.5 mm²
Conductor cross section flexible min.
0.14 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.34 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 4.1
27141100
ECLASS 9.0
27141120
ETIM 6.0
EC000897
UNSPSC 19.0
39121410
ECLASS 4.0
27141100
ECLASS 7.0
27141120
UNSPSC 13.2
39121410
ETIM 7.0
EC000897