3069843 Phoenix Contact Terminal Blocks

Product Details

• Plate thickness
  1 mm ... 4 mm
• Test directions
  X-, Y- and Z-axis (pos. and neg.)
• Shock form
  Half-sine
• Static insulating material application in cold
  -60 °C
• Surface flammability NFPA 130 (ASTM E 162)
  passed
• Fire protection for rail vehicles (DIN EN 45545-2) R24
  HL 1 - HL 3
• Number of levels
  1
• Potentials
  20
• Maximum power dissipation for nominal condition
  1.31 W
• Nominal voltage UN
  400 V AC/DC
• Back of the hand protection
  guaranteed
• Result of surge voltage test
  Test passed
• Bending test rotation speed
  10 rpm
• Result of tight fit on support
  Test passed
• Setpoint
  5 N
• Short circuit stability result
  Test passed
• Ageing test for screwless modular terminal block temperature cycles
  192
• ASD level
  6.12 (m/s2)2/Hz
• Connection
  1 level
• Number of connections
  40
Color
gray
Test surge voltage
5 kV
Open side panel
No
Finger protection
guaranteed
Note regarding shock protection
When test disconnect plug is plugged in.
Power frequency withstand voltage setpoint
1.89 kV
Tensile test result
Test passed
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Pitch
8.2 mm
Connection in acc. with standard
IEC 60947-7-1
Conductor cross section flexible max.
6 mm²
Result of temperature-rise test
Test passed
Short-time current
0.15 kA
Result of aging test
Test passed
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Shock duration
18 ms
Mounting type
Wall mounting
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Nominal cross section
6 mm²
Rated surge voltage
4 kV
Flammability rating according to UL 94
V0
Insulating material group
I
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Result of power-frequency withstand voltage test
Test passed
Result of flexion and pull-out test
Test passed
Bending test conductor cross section/weight
0.5 mm² / 0.3 kg
Acceleration
30g
Shock test result
Test passed
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Note
The measuring transducer block is replaced every 100 cycles.
Proof of thermal characteristics (needle flame) effective duration
30 s
Conductor cross section short circuit testing
4 mm²
Width
196.8 mm
Height
56.5 mm
Stripping length
12 mm
Conductor cross section AWG min.
20
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Max. AWG conductor cross section, flexible
10
Number of positions
20
Insulating material
PA
Overvoltage category
III
Maximum load current
30 A (with 6 mm² conductor cross section)
Terminal block mounting
0.8 Nm ... 1 Nm
Bending test turns
135
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Result of voltage-drop test
Test passed
Calorimetric heat release NFPA 130 (ASTM E 1354)
27,5 MJ/kg
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Result of thermal test
Test passed
Oscillation, broadband noise test result
Test passed
Test spectrum
Service life test category 2, bogie-mounted
Test duration per axis
5 h
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Number of shocks per direction
3
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Length
81 mm
Connection method
Push-in connection
Conductor cross section flexible min.
0.5 mm²
Conductor cross section solid max.
10 mm²
Conductor cross section solid min.
1 mm²
Conductor cross section AWG max.
8
ECLASS 5.0
27141100
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Max. tightening torque of the mounting screw:
1 Nm
Ambient temperature (assembly)
-5 °C ... 70 °C
REACh SVHC
Lead 7439-92-1
ETIM 7.0
EC000902
Conductor cross section flexible, with ferrule with plastic sleeve min.
1 mm²
Connection cross sections directly pluggable
1 mm² 10 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
Internal cylindrical gage
A5
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 5.1
27141100
ETIM 4.0
EC000897
UNSPSC 19.0
39121410
Min. AWG conductor cross section, flexible
20
Conductor cross section flexible, with ferrule without plastic sleeve min.
1 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
Min. tightening torque of the mounting screw:
0.8 Nm
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 11.0
27141126
ECLASS 9.0
27141126
UNSPSC 20.0
39121410
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 10.0.1
27141126
ECLASS 6.0
27141100
ECLASS 7.0
27141126
UNSPSC 13.2
39121410
UNSPSC 21.0
39121410
UNSPSC 18.0
39121410
ETIM 6.0
EC000902