2907160 Phoenix Contact UPS (DC)

2907160 Product Details

• Width
  60 mm
• Depth
  115 mm
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
• Max. permissible relative humidity (operation)
  ≤ 95 % (At +25°C, non-condensing)
• Degree of pollution
  2
• Nominal output voltage
  24 V DC
• Derating
  > 60 °C (2.5%/K of POut nom.)
• Residual ripple
  < 20 mV
• Protection class
  I
• Assembly instructions
  alignable: horizontally 0 mm, vertically 50 mm
• EMC requirements for noise emission
  EN 61000-6-3
• Standard - Safe isolation
  DIN VDE 0100-410
• Conducted noise emission
  EN 61000-6-3 (Class B)
• DNV GL noise radiation
  Class B
• Test field strength
  10 V/m (Test Level 3)
• Fast transients (burst)
  EN 61000-4-4
• Voltage
  10 V (Test Level 3)
• ECLASS 11.0
  27040705
• Utilization restriction
  EMC: class A product, see manufacturer's declaration in the download area
• Installation distance top/bottom
  50 mm / 50 mm
Climatic class
3K3 (in acc. with EN 60721)
Inrush current limiting/I²t
< 0.43 A2s
Nominal output current (IN)
5 A
Control deviation
< 0.75 % (Static load change 10 % ... 90 %)
Connection in parallel
yes, with diode module uncoupled
Mounting position
horizontal DIN rail NS 35, EN 60715
Connection method
Push-in connection
Conductor cross section AWG min.
24
EMC requirements for noise immunity
EN 61000-6-1
Standard - power supply devices for low voltage with DC output
EN 61204-3
Noise emission
EN 61000-6-3 (Class B)
DNV GL conducted interference
Class B
Comments
Criterion B
Conducted interference
EN 61000-4-6
ECLASS 10.0.1
27040705
ECLASS 9.0
27040705
Width with alternative assembly
115 mm
Installation distance right/left
0 mm / 0 mm
Ambient temperature (start-up type tested)
-40 °C
Typical response time
60 ms
Input fuse, integrated
6.3 A (slow-blow, internal)
Surge protection against internal surge voltages
< 30 V DC
MTBF (IEC 61709, SN 29500)
> 1395470 h (230 V AC, at 25 °C)
Conductor cross section solid min.
0.2 mm²
Conductor cross section flexible max.
1.5 mm²
Charge characteristic curve
IU0U
UL approvals
UL Listed UL 61010
Electrostatic discharge
EN 61000-4-2
Discharge in air
8 kV (Test Level 4)
Contact discharge
6 kV (Test Level 4)
Criterion A
Normal operating behavior within the specified limits.
Attenuated sinusoidal oscillations (ring wave)
EN 61000-4-12
ETIM 6.0
EC000382
Height
130 mm
Depth with alternative assembly
60 mm
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Ambient temperature (storage/transport)
-40 °C ... 85 °C
AC input voltage range
100 V AC ... 240 V AC -15 % ... +10 %
Setting range of the output voltage (USet)
24 V DC ... 28 V DC (> 24 V constant capacity)
Maximum power dissipation in no-load condition
< 3 W (230 V AC)
Efficiency
typ. 85 % (120 V AC)
Feedback voltage resistance
≤ 35 V DC
Conductor cross section solid max.
1.5 mm²
Stripping length
8 mm
Standard – Safety extra-low voltage
IEC 61010 (SELV) / (PELV)
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Additional text
Bridge and deck area
Electromagnetic HF field
EN 61000-4-3
Input
2 kV (symmetrical)
I/O/S
asymmetrical
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ETIM 7.0
EC000382
Height with alternative assembly
130 mm
Degree of protection
IP20
Installation height
≤ 4000 m (> 2000 m, observe derating)
Mains buffering time
≥ 15 ms (120 V AC)
Dynamic Boost (IDyn.Boost)
7.5 A
Net weight
0.75 kg
Insulation voltage input/output
3 kV AC (type test)
Conductor cross section flexible min.
0.2 mm²
Conductor cross section AWG max.
16
Charge current
0.2 A ... 1.5 A (-25 °C ... 60 °C)
Standard - safety for equipment for measurement, control, and laboratory use
IEC 61010-1
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Frequency range
0.15 MHz ... 80 MHz
Output
1 kV (Test Level 1 - symmetrical)
Signal
1 kV (Test Level 2 - asymmetrical)
REACh SVHC
Lead 7439-92-1

Product condition