2907069 Phoenix Contact UPS (DC)

2907069 Product Details

• Depth
  125 mm
• Installation distance right/left (active, passive)
  0 mm / 0 mm (POut ≤50 %)
• Installation distance top/bottom (active)
  50 mm / 50 mm (POut ≥50% )
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
• Degree of pollution
  2
• Installation height
  ≤ 4000 m
• Switch-on time
  max. 3 s
• Energy storage device connection in parallel
  Yes, 5 (observe line protection)
• UPS connection in parallel
  no
• Battery technology
  VRLA, VRLA-WTR, LI-ION
• End-of-charge voltage (temperature-compensated)
  25 V DC ... 32 V DC
• End-of-charge voltage
  32 V DC
• Temperature sensor
  yes
• Life expectancy (electrolytic capacitors)
  137895 h
• Conductor cross section solid max.
  2.5 mm²
• Conductor cross section flexible min.
  0.2 mm²
• Tightening torque, min
  0.5 Nm
• Designation
  CB scheme
• Electrostatic discharge
  EN 61000-4-2
• Frequency range
  50 Hz ... 60 Hz
Fast transients (burst)
EN 61000-4-4
Input
1 kV (Test Level 3 - symmetrical)
I/O/S
asymmetrical
Criterion A
Normal operating behavior within the specified limits.
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
UNSPSC 13.2
39121004
UNSPSC 21.0
39121011
Height
130 mm
Depth with alternative assembly
37 mm
Installation distance top/bottom (active, passive)
40 mm / 20 mm (POut ≤50 %)
Installation distance top/bottom (passive)
40 mm / 20 mm (POut ≥50% )
Climatic class
3K3 (EN 60721)
Electric strength, max.
35 V DC
Short-circuit-proof
yes
Voltage drop, input/output
0.4 V DC
Energy storage device connection in series
no
Output voltage range
19 V DC ... 32 V DC
Nominal capacity (without additional charger)
1.2 Ah ... 60 Ah
Temperature compensation (configurable)
42 mV/K
Deep discharge protection
19.2 V DC
Conductor cross section solid min.
0.2 mm²
Conductor cross section flexible max.
2.5 mm²
Single conductor/terminal point, stranded, with ferrule, max.
2.5 mm²
Stripping length
6.5 mm
Standard designation
Safety extra-low voltage
Standards/regulations
IEC 61010-1 (SELV)
Discharge in air
15 kV (Test Level 4)
Electromagnetic HF field
EN 61000-4-3
Output
1 kV (Test Level 3 - symmetrical)
Additional text
DC, 60 s
REACh SVHC
Lead 7439-92-1
ECLASS 10.0.1
27040705
ETIM 6.0
EC000382
UNSPSC 19.0
39121011
Width
35 mm
Width with alternative assembly
123 mm
Installation distance right/left (passive)
0 mm / 0 mm (POut ≥50% )
Degree of protection
IP20
Ambient temperature (start-up type tested)
-40 °C
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Input voltage range
18 V DC ... 30 V DC
Inrush current
≤ 7 A (≤ 4 ms)
Fixed backup threshold
22 V DC
Switch-over time
0 ms
UPS connection in series
no
Static Boost (IStat.Boost)
12.5 A
Dynamic Boost (IDyn.Boost)
20 A (5 s)
Charging current (configurable)
3 A
IQ-Technology
yes
Charge characteristic curve
IU0U
Environmental protection directive
RoHS Directive 2011/65/EU
Connection method
Screw connection
Conductor cross section AWG min.
30
Conductor cross section AWG max.
12
EMC requirements for noise emission
EN 61000-6-3
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Test field strength
300 A/m
Signal
1 kV (Test Level 2 - asymmetrical)
Power frequency magnetic field
EN 61000-4-8
Frequency
0 Hz
ECLASS 9.0
27040705
ETIM 7.0
EC000382
UNSPSC 20.0
39121011
Height with alternative assembly
130 mm
Installation distance right/left (active)
5 mm / 5 mm (POut ≥50% )
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Input voltage
24 V DC
Reverse polarity protection
yes
Internal input fuse
no
No-load proof
yes
Efficiency
typ. 97 %
Selective Fuse Breaking (ISFB)
60 A (15 ms)
Max. capacity
80 Ah
Buffer time
25 min. (7.2 Ah)
Charging time
120 h
MTBF (IEC 61709, SN 29500)
> 1189000 h (25 °C)
Weight
0.5 kg
Single conductor/terminal point, stranded, with ferrule, min.
0.2 mm²
Tightening torque max
0.6 Nm
EMC requirements for noise immunity
EN 61000-6-1
Identification
IEC 61010-1
Contact discharge
8 kV (Test Level 4)
Comments
Criterion A
Conducted interference
EN 61000-4-6
Surge voltage load (surge)
EN 61000-4-5
Voltage
10 V (Test Level 3)
ECLASS 11.0
27040705
ECLASS 5.1
27242213
UNSPSC 18.0
39121011

Product condition