2906367 Phoenix Contact UPS (DC)

2906367 Product Details

• Width
  88 mm
• Height with alternative assembly
  130 mm
• Degree of protection
  IP20
• Max. permissible relative humidity (operation)
  ≤ 95 % (At +25°C, non-condensing)
• Inrush current limiting/I²t
  < 0.76 A2s
• Typical response time
  200 ms
• Maximum power dissipation in no-load condition
  < 3.6 W (400 V AC)
• Residual ripple
  < 20 mV
• Net weight
  1.71 kg
• Depth
  160 mm
• Installation distance right/left
  0 mm / 0 mm
• Installation distance top/bottom
  50 mm / 50 mm
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
• Climatic class
  3K3 (in acc. with EN 60721)
• Nominal output voltage
  24 V DC
• Nominal output current (IN)
  20 A
• Control deviation
  < 0.3 % (Static load change 10 % ... 90 %)
• Feedback voltage resistance
  ≤ 35 V DC
• Protection class
  I
• Conductor cross section flexible min.
  0.2 mm²
Stripping length
8 mm
Charge characteristic curve
IU0U
Standard – Safety extra-low voltage
IEC 61010 (SELV) / (PELV)
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Noise emission
EN 61000-6-3 (Class B)
Discharge in air
8 kV (Test Level 4)
Output
1 kV (Test Level 1 - symmetrical)
Attenuated sinusoidal oscillations (ring wave)
EN 61000-4-12
ETIM 7.0
EC000382
ECLASS 11.0
27040705
Conducted noise emission
EN 61000-6-3 (Class B)
DNV GL noise radiation
Class B
Frequency range
0.15 MHz ... 80 MHz
Comments
Criterion A
I/O/S
asymmetrical
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ETIM 6.0
EC000382
Width with alternative assembly
160 mm
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Mains buffering time
≥ 25 ms (400 V AC)
Input fuse, integrated
6.3 A (slow-blow, internal)
Setting range of the output voltage (USet)
24 V DC ... 28 V DC (> 24 V constant capacity)
Efficiency
typ. 93 % (400 V AC)
Surge protection against internal surge voltages
< 30 V DC
Insulation voltage input/output
4 kV AC (type test)
Mounting position
horizontal DIN rail NS 35, EN 60715
Conductor cross section solid max.
1.5 mm²
Conductor cross section AWG min.
24
Standard - safety for equipment for measurement, control, and laboratory use
IEC 61010-1
UL approvals
UL Listed UL 61010
DNV GL conducted interference
Class B
Electromagnetic HF field
EN 61000-4-3
Input
2 kV (symmetrical)
Voltage
10 V (Test Level 3)
ECLASS 9.0
27040705
Height
130 mm
Depth with alternative assembly
88 mm
Ambient temperature (start-up type tested)
-40 °C
Degree of pollution
2
Installation height
≤ 4000 m (> 2000 m, observe derating)
AC input voltage range
2x 400 V AC ... 500 V AC -10 % ... +10 %
Dynamic Boost (IDyn.Boost)
30 A
Derating
> 60 °C (2.5%/K of POut nom.)
Connection in parallel
yes, with diode module uncoupled
MTBF (IEC 61709, SN 29500)
> 1108720 h (400 V AC, at 25°C)
Connection method
Push-in connection
Conductor cross section solid min.
0.2 mm²
Conductor cross section AWG max.
16
EMC requirements for noise immunity
EN 61000-6-1
EMC requirements for noise emission
EN 61000-6-3
Standard - power supply devices for low voltage with DC output
EN 61204-3
Additional text
Bridge and deck area
Electrostatic discharge
EN 61000-4-2
Fast transients (burst)
EN 61000-4-4
Conducted interference
EN 61000-4-6
REACh SVHC
Lead 7439-92-1
Assembly instructions
alignable: horizontally 0 mm, vertically 50 mm
Conductor cross section flexible max.
1.5 mm²
Charge current
0.5 A ... 3 A (-25 °C ... 60 °C)
Standard - Safe isolation
DIN VDE 0100-410
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Contact discharge
6 kV (Test Level 4)
Test field strength
10 V/m (Test Level 3)
Signal
1 kV (Test Level 2 - asymmetrical)
Criterion A
Normal operating behavior within the specified limits.
ECLASS 10.0.1
27040705

Product condition