2702532 Phoenix Contact Data & Networking Devices

2702532 Product Details

• Width
  45 mm
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Altitude
  ≤ 5000 m (For restrictions, see the manufacturer's declaration for altitude operation)
• Electromagnetic compatibility
  Conformance with RED Directive 2014/53/EU
• MTTF
  383 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
• Conductor cross section flexible, with ferrule without plastic sleeve
  0.25 mm² ... 1.5 mm²
• Ambient temperature (operation)
  -40 °C ... 70 °C (Maximum transmission power 5 dBm)
• Electrical isolation
  VCC // LTE // Ethernet // PE
• Color
  gray
• Max. current consumption
  1.7 A
• Conductor cross section flexible min.
  0.14 mm²
• Stripping length
  9 mm
• Transmission length
  100 m (shielded twisted pair)
• SIM interface 1
  1.8 volt, 3 volt
• Number of VPN tunnels
  3
• Description of the input
  Digital input
• Voltage input signal
  10 V DC ... 30 V DC
• Test result
  15g
• ECLASS 6.0
  19170100
• ETIM 7.0
  EC001478
Depth
126 mm
Degree of protection
IP20 (Manufacturer's declaration)
Mounting type
DIN rail mounting
Degree of pollution
2
Typical current consumption
< 200 mA (24 V DC)
Conductor cross section flexible max.
1.50 mm²
Conductor cross section solid max.
1.50 mm²
No. of ports
2 (SELV)
Frequency range
0.15 MHz ... 80 MHz
Antenna
50 Ω impedance SMA antenna socket
Number of outputs
1
Switching level "1" signal
10 V DC ... 30 V DC
Type of test
Shock in acc. with EN 60068-2-27/IEC 60068-2-27
ECLASS 10.0.1
19170502
Comments
Criterion B
ECLASS 11.0
19170502
Height
130 mm
Permissible humidity (operation)
10 % ... 95 % (non-condensing)
Noise immunity
EN 61000-6-2
Net weight
266 g
Supply voltage range
10 V DC ... 30 V DC (SELV, via pluggable Push-in terminal block)
Conductor cross section, flexible, with ferrule, with plastic sleeve
0.25 mm² ... 0.75 mm²
Conductor cross section solid min.
0.14 mm²
Interface 1
Ethernet interface, 10/100Base-T(X) in accordance with IEEE 802.3
Auxiliary protocols
ARP, DHCP, PING (ICMP), SNMP V1/V2, SMTP(S), NTP, SSL/TLS, STARTTLS
Operating mode
Indoor use only
Serial transmission speed
10/100 Mbps, auto negotiation
Management
Web-based management, SNMP
Output name
Digital output
Designation
Corrosive gas test
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.1
19030100
ETIM 6.0
EC001478
Utilization restriction
Use in potentially explosive areas is not permitted in China.
Permissible humidity (storage/transport)
10 % ... 95 % (non-condensing)
Housing material
Plastic
Wireless licences
USA
Connection method
RJ45 jack, shielded
Conductor cross section AWG max.
16
Interface
Ethernet
Data rate
≤ 150 Mbps (LTE (DL))
Country support
USA
Voltage output signal
10 V DC ... 30 V DC (depending on the operating voltage)
Number of inputs
2
Identification
ISA-S71.04-1985 G3 Harsh Group A
Contact discharge
± 6 kV (Test Level 3)
Signal
± 1 kV (Data line, asymmetrical)
ECLASS 7.0
19170103
Conductor cross section AWG min.
26
Protocols supported
TCP/IP, UDP/IP, FTP, HTTP(S)
Interface description
LTE (FDD)
LTE
CAT4
Web-based management
yes
Security functions
Supported 3DES, AES-128, -192, -256 ESP tunnel X.509v3, PSK MD5, SHA-1 RFC 3706 IP, port, protocol
Current output signal
≤ 50 mA (Not short-circuit proof)
Standards/regulations
EN 61000-4-6
ECLASS 5.0
19030100
ECLASS 9.0
19170103

Product condition