1295694 Phoenix Contact Electrical Wires & Cables

1295694 Product Details

• Standards/regulations
  DIN EN 60751
• Depth
  122.8 mm
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Type
  Locking actuator top
• Charging mode
  Mode 4
• Height
  151.2 mm
• Maximum charging power
  200 kW
• Rated current of power contacts
  200 A DC
• Type of signal transmission
  Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
• Mounting position of the locking actuator
  Top center
• Flammability rating
  V0
• Cable structure
  4 x 0.5 mm²
• Outer sheath, material
  PVC
• Number of positions of theconnectors
  4
• Pause time after entry or exit path
  3 s
• Lock recognition
  available
• Temperature coefficient (TCR)
  3850 ppm/K
• ECLASS 11.0
  27144706
• Application
  For charging with direct current (DC)
• Charging standard
  CCS type 1
Note on the connection method
Crimp connection, cannot be disconnected
Bore dimensions
117.6 mm x 90 mm, 117.6 mm x 83 mm
Max. altitude
4000 m (above sea level)
Number of phases
1
Rated voltage for signal contacts
30 V AC
Rated voltage for power contacts
1000 V DC
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Design line
Generation 4
Material
Plastic
External cable diameter
1.6 mm -0.2 mm
Single wire, color
black PP/CS
Maximum voltage for locking detection
12 V
Max. dwell time with reverse current
1 s
Type of sensor
Pt 1000
Mechanical emergency release
available
Shutdown temperature
90 °C
Design
Generation 4
Note
A protective cap is supplied as standard for the DC contacts.
Width
108 mm
Ambient temperature (operation)
-40 °C ... 80 °C
Type of charging current
DC
Rated current for signal contacts
2 A
Insertion/withdrawal cycles
> 10000
Required mounting screws
M6
Mounting hole diameter
6.80 mm (ø)
Material surface of contacts
Ag
Minimum bending radius
15 mm
Possible power supply range at the motor
9 V ... 16 V
Reverse current of the motor
max. 1.5 A
Recommended adaptation time
600 ms
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
Temperature range
-40 °C ... 130 °C
Conductor length
8 m (DC cables)
Number of power contacts
5 (L1, N, PE, DC+, DC-)
Insulation resistance of neighboring contacts
> 200 MΩ
Insertion force
< 100 N
Locking type
Locking in the inserted state with a locking mechanism
Cable resistance
≤ 37.1 Ω/km
Cable weight
7 kg/km
Operating voltage
12 V (Typical power supply at the motor)
Service life insertion cycles
> 10000 load cycles
Tolerance at the sensor with the recommended measured current
±3K
ECLASS 9.0
27144706
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Number of signal contacts
2 (CP, CS)
Resistor coding
2.7 kΩ (between PE and CS)
Withdrawal force
< 100 N
Screws included in the scope of delivery
none
Housing color
black
Customer variations
On request
External sheath, color
Green-yellow
Typical motor current for locking
0.25 A
Cable length
1 m
Long-term stability (max. R0-Drift)
≤ 0.1 % (After 1000 hours at 130°C)
ECLASS 10.0.1
27144706

Product condition