1017064 Phoenix Contact Electrical Safety Devices

1017064 Product Details

• Ambient temperature (operation)
  -25 °C ... 60 °C (observe derating)
• Maximum altitude
  ≤ 2000 m (Above sea level)
• Filter time
  2 ms (at A1-A2 in the event of voltage dips at Us)
• Diagnostic supply voltage UD
  24 V DC -20 % / +25 %
• Current consumption
  typ. 20 mA (Input TP1)
• Protective circuit/component
  36 V suppressor diode
• Contact type
  1 signaling current path
• Diagnostic threshold
  7 Ω ... 20 kΩ (configurable)
• Typical pickup time at US
  typ. 100 ms (when controlled via A1-A2)
• Nominal operating mode
  100% operating factor
• Utilization restriction
  Use in potentially explosive areas is not permitted in China.
• Max. permissible humidity (storage/transport)
  75 % (on average, 85% infrequently, non-condensing)
• Rated control supply current IS
  typ. 75 mA
• Input current at UD
  35 mA (at UD = 24 V)
• Protective circuit
  Surge protection 36 V suppressor diode (A1-A2)33 V suppressor diode (24V-GND)
• Output name
  Signaling current path
• Sq. Total current
  9 A2 (observe derating)
• Mechanical service life
  approx. 5x 107 cycles
• Typical release time at US
  typ. 30 ms (when controlled via A1-A2)
• Mounting position
  vertical or horizontal
Min. degree of protection of inst. location
IP54
Status display
1 x yellow LED, 1 x green LED, 1 x red LED
Conductor cross section flexible
0.2 mm² ... 1.5 mm²
Conductor cross-section flexible with ferrule without plastic sleeve
0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Standards/regulations
DIN EN 50178
Vibration (operation)
10 Hz ... 150 Hz, 2g
ECLASS 11.0
27371819
ECLASS 6.0
27371819
Height
117.4 mm
Air pressure (operation)
79 kPa ... 106 kPa
Power consumption at US
typ. 2 W (at US/UD; On state)
Inrush current at UD
1.5 A (Δt < 10 µs)
Number of inputs
3
Number of outputs
1 (without delay, floating)
Limiting continuous current
3 A (Observe derating, load type, and on-load voltage)
Recovery time
1 s (when controlled via A1-A2)
Net weight
147.16 g
pluggable
Yes
Stripping length
8 mm
Rated insulation voltage
250 V AC
Shock
15g, 11 ms
ECLASS 5.1
27371901
ETIM 6.0
EC001449
Depth
114.5 mm
Max. permissible relative humidity (operation)
75 % (on average, 85% infrequently, non-condensing)
Inrush current
max. 800 mA (Δt  100 ms)
Power consumption at UD
typ. 0.9 W (at UD; Off state)
Type of protection
Surge protection
Output description
non-safety-related N/C contact
Switching capacity
min. 1 W
Short-circuit protection
no
Relay type
Electromechanical relay
Assembly instructions
See derating curve
Housing color
yellow
Conductor cross section solid
0.2 mm² ... 1.5 mm²
Safety Integrity Level (SIL)
3 (Reference IEC 61508)
Overvoltage category
III
Conformance
CE-compliant
ETIM 7.0
EC001449
Width
17.5 mm
Ambient temperature (storage/transport)
-40 °C ... 65 °C
Air pressure (storage/transport)
79 kPa ... 106 kPa
Rated control circuit supply voltage US
24 V DC -15 % / +10 %
Description of the input
Test point for proof test
Contact material
AgNi, gold-flashed, Ag alloy
Switching voltage
min. 16 V AC/DC
Switching frequency
max. 0.5 Hz
Mounting type
DIN rail mounting
Degree of protection
IP20
Conductor cross-section flexible with ferrule and plastic sleeve
0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Rated surge voltage/insulation
Basic insulation 4 kV between all current paths and housing
REACh SVHC
Lead 7439-92-1
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 9.0
27371819
Housing material
Frianyl A 63 R V0
Connection method
Push-in connection
Conductor cross-section AWG
24 ... 16
Designation
Air clearances and creepage distances between the power circuits
Degree of pollution
2
Environmental simulation test
ISA-S71.04 (G3)
ECLASS 10.0.1
27371819

Product condition