LGM50 Pepperl + Fuchs Electronic Components

Product Details

• Mass
  see Table 1, max. 1650 g (per profile)
• Cable length
  max. 30 m
• Optical face
  Plastic pane , Polycarbonate
• Housing
  extruded aluminum section , Silver anodized
• Connection
  Emitter: connecting cable with 4-pin, M12 x 1 connector , 330 mm total length, Receiver: connecting cable with 8-pin, M12 x 1 connector , 350 mm total length
• Degree of protection
  IP67
• Conductor cross section
  min. 0.25 mm²
• Housing depth
  30.5 mm
• Housing length L
  see Table 1, max. 3160 mm
• Housing width
  20 mm
• Ambient temperature
  -30 ... 60 °C (-22 ... 140 °F)
• Storage temperature
  -30 ... 70 °C (-22 ... 158 °F)
• Protection class
  III ( IEC 61140 )
• Timer function
  Off-delay programmable from 0 ... 1.25 s in 5 ms steps (adjustment via IO-Link only)
• CCC approval
  CCC approval / marking not required for products rated ≤36 V
• UL approval
  cULus Listed
• Switching frequency
  see Table 1, max. 129 Hz
• Product standard
  EN 60947-5-2
• Response time
  see Table 1, max. 8 ms
• EAC conformity
  TR CU 020/2011
Communication interface
IEC 61131-9
Voltage drop
≤ 2 V DC
Signal output
Command interface: Pin 4 IO-Link interface C or used as switching output Q; 1 short-circuit proof reverse polarity protected push-pull output (receiver), Switch output: Pin 5 switching output Q; 1 short-circuit proof reverse polarity protected push-pull o
Stability alarm output
Stability Control (SC) 1 PNP, short-circuit protected, reverse polarity protected on pin 2 (receiver)
Switching threshold
Factory setting: The signal tracking for the threshold value is deactivated, increasing the optical resolution by a maximum of 4 mm; switchable to active signal tracking
Switching voltage
max. 30 V DC
Switching type
Factory setting: dark on , Switchable to light-on mode
Test input
Emitter switch-off with +UB or 0 V at pin 4 (emitter)
Switching current
max. 100 mA
SIO mode support
yes
Function input
Range input activation from 1.6 m with +UB or 0 V on pin 2 (emitter), Teach-In input for parameterization on pin 8 (receiver)
Min. cycle time
2.3 ms
Process data width
16 bit
Operating voltage
18 ... 30 V DC
COM-Mode
COM2 (38.4 kBit/s)
Device ID
1050371 ... 1050398 ( 0x100703 ... 0x10071E )
Interface type
IO-Link ( pin 4 )
IO-Link revision
1.0
Time delay before availability
see Table 1, max. 1.5 s
No-load supply current
Emitter ≤: 50 mA, Receiver: ≤ 150 mA (without outputs)
Ripple
10 %
Diagnostic Coverage (DC)
60 %
Control elements
Receiver: 2 touch buttons for programming
Mission Time (TM)
20 a
Opening angle
10 °
Operation indicator
LED green: constantly on - power-on, double pulse flashing (0.8 Hz) - undervoltage, flashing (4 Hz) - short circuit, flashing with short interruptions (1 Hz) - IO-Link mode
Optical resolution
without beam crossover: 50 mm, with beam crossover: 25 mm with in 25%  and  75% of the range
Status indicator
Emitter: LED yellow, constantly on - high emitter power, constantly off - low emitter power, flashing (8 Hz) - error message, Receiver: LED yellow: constantly on - object detected, constantly off - no object detected, flashing (4 Hz) - below stability con
Ambient light limit
> 50000 Lux (if external light source is outside the opening angle)
MTTFd
56 a
Operating mode
Emitter: Emitter power adjustable in two ranges
Beam spacing
50 mm
Field height
see Table 1, max. 3000 mm
Beam blanking
adjustable max. 2 fixed suppressible beam areas (blanking)
Light source
IRED
Beam crossover
Factory setting: three beam crossing, deactivateable
Number of beams
see Table 1, max. 61
Effective detection range
Standard : 0.3 ... 6 m
Light type
modulated infrared light , 850 nm
Threshold detection range
7.5 m

Related documents LGM50 Specs