LGM17 Pepperl + Fuchs Electronic Components

Product Details

• Cable length
  max. 30 m
• Housing depth
  30.5 mm
• Mass
  see Table 1, max. 1750 g (per profile)
• Housing
  extruded aluminum section , Silver anodized
• Optical face
  Plastic pane , Polycarbonate
• Housing length L
  see Table 1, max. 3360 mm
• Degree of protection
  IP67
• Connection
  Emitter: connecting cable with 4-pin, M12 x 1 connector , 330 mm total length, Receiver: connecting cable with 8-pin, M12 x 1 connector , 350 mm total length
• Housing width
  20 mm
• Conductor cross section
  min. 0.25 mm²
• Storage temperature
  -30 ... 70 °C (-22 ... 158 °F)
• Ambient temperature
  -30 ... 60 °C (-22 ... 140 °F)
• UL approval
  cULus Listed
• CCC approval
  CCC approval / marking not required for products rated ≤36 V
• Protection class
  III ( IEC 61140 )
• Product standard
  EN 60947-5-2
• EAC conformity
  TR CU 020/2011
• Communication interface
  IEC 61131-9
• Response time
  see Table 1, max. 16 ms
• Timer function
  Off-delay programmable from 0 ... 1.25 s in 5 ms steps (adjustment via IO-Link only)
Switching frequency
see Table 1, max. 129 Hz
Switching voltage
max. 30 V DC
Switching current
max. 100 mA
Stability alarm output
Stability Control (SC) 1 PNP, short-circuit protected, reverse polarity protected on pin 2 (receiver)
Switching threshold
Factory setting: The signal tracking for the threshold value is deactivated, increasing the optical resolution by a maximum of 4 mm; switchable to active signal tracking
Voltage drop
≤ 2 V DC
Switching type
Factory setting: dark on , Switchable to light-on mode
Signal output
Command interface: Pin 4 IO-Link interface C or used as switching output Q; 1 short-circuit proof reverse polarity protected push-pull output (receiver), Switch output: Pin 5 switching output Q; 1 short-circuit proof reverse polarity protected push-pull o
Test input
Emitter switch-off with +UB or 0 V at pin 4 (emitter)
Function input
Range input activation from 1.6 m with +UB or 0 V on pin 2 (emitter), Teach-In input for parameterization on pin 8 (receiver)
SIO mode support
yes
Min. cycle time
2.3 ms
COM-Mode
COM2 (38.4 kBit/s)
Process data width
16 bit
IO-Link revision
1.0
Interface type
IO-Link ( pin 4 )
Ripple
10 %
Device ID
1050369 ... 1050400 ( 0x100701 ... 0x100720 )
No-load supply current
Emitter ≤: 50 mA, Receiver: ≤ 150 mA (without outputs)
Time delay before availability
see Table 1, max. 3 s
Operating voltage
18 ... 30 V DC
MTTFd
25 a
Control elements
Receiver: 2 touch buttons for programming
Status indicator
Emitter: LED yellow, constantly on - high emitter power, constantly off - low emitter power, flashing (8 Hz) - error message, Receiver: LED yellow: constantly on - object detected, constantly off - no object detected, flashing (4 Hz) - below stability con
Diagnostic Coverage (DC)
60 %
Opening angle
10 °
Operation indicator
LED green: constantly on - power-on, double pulse flashing (0.8 Hz) - undervoltage, flashing (4 Hz) - short circuit, flashing with short interruptions (1 Hz) - IO-Link mode
Mission Time (TM)
20 a
Ambient light limit
> 50000 Lux (if external light source is outside the opening angle)
Optical resolution
without beam crossover: 17 mm, with beam crossover: 8.5 mm with in 25%  and  75% of the range
Operating mode
Emitter: Emitter power adjustable in two ranges
Light source
IRED
Threshold detection range
7.5 m
Field height
see Table 1, max. 3200 mm
Light type
modulated infrared light , 850 nm
Beam spacing
16.67 mm
Beam crossover
Factory setting: three beam crossing, deactivateable
Beam blanking
adjustable max. 2 fixed suppressible beam areas (blanking)
Number of beams
see Table 1, max. 193
Effective detection range
Standard : 0.3 ... 6 m

Related documents LGM17 Specs