3046168 Phoenix Contact Terminal Blocks

Product Details

• Number of connections
  2
• Rated surge voltage
  6 kV
• Insulating material group
  I
• Nominal current IN
  20 A (with 4 mm² conductor cross section)
• Surge voltage test setpoint
  7.2 kV
• Result of the test for mechanical stability of terminal points (5 x conductor connection)
  Test passed
• Requirement temperature-rise test
  Increase in temperature ≤ 45 K
• Result of thermal test
  Test passed
• Insulating material
  PA
• Maximum load current
  20 A (with 6 mm² conductor cross section)
• Shock protection test specification
  DIN EN 50274 (VDE 0660-514):2002-11
• Result of power-frequency withstand voltage test
  Test passed
• Bending test rotation speed
  10 rpm
• Tractive force setpoint
  80 N
• Requirements, voltage drop
  U1 ≤ 6,4 mV (1,6 mV x number of conductorclamping units or disconnect unit contactpoints)U2 ≤ 1,5 x U1
• Test specification, oscillation, broadband noise
  DIN EN 50155 (VDE 0115-200):2018-05
• Test duration per axis
  5 h
• Number of shocks per direction
  3
• Surface flammability NFPA 130 (ASTM E 162)
  passed
• Width
  6.2 mm
Screw thread
M3
Connection in acc. with standard
CSA
Color
gray
Degree of pollution
3
Nominal voltage UN
500 V
Result of surge voltage test
Test passed
Result of flexion and pull-out test
Test passed
Tensile test result
Test passed
Conductor cross section short circuit testing
2.5 mm²
ASD level
6.12 (m/s2)2/Hz
Shock form
Semi-sinusoidal
Static insulating material application in cold
-60 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
27,5 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Height NS 35/7,5
47.5 mm
Conductor cross section solid min.
0.14 mm²
Conductor cross section flexible max.
6 mm²
Min. AWG conductor cross section, flexible
26
Conductor cross section flexible, with ferrule with plastic sleeve max.
4 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, minimum
0.14 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
ECLASS 5.0
27141100
ETIM 4.0
EC000902
UNSPSC 18.0
39121410
Note
The max. load current must not be exceeded by the total current of all connected conductors.
Potentials
1
Area of application
Railway industry
Maximum power dissipation for nominal condition
1.02 W
Open side panel
No
Finger protection
guaranteed
Bending test conductor cross section/weight
0.14 mm² / 0.2 kg
Tight fit on carrier
NS 35
Short circuit stability result
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Tightening torque, min
0.6 Nm
Conductor cross section solid max.
6 mm²
Max. AWG conductor cross section, flexible
10
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.14 mm²
2 conductors with same cross section, stranded min.
0.14 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
2.5 mm²
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 10.0.1
27141126
ECLASS 4.1
27141100
ECLASS 6.0
27141100
ETIM 3.0
EC000902
ETIM 6.0
EC000902
UNSPSC 11
39121410
UNSPSC 13.2
39121410
Number of levels
1
Nominal cross section
4 mm²
Flammability rating according to UL 94
V0
Overvoltage category
III
Back of the hand protection
guaranteed
Power frequency withstand voltage setpoint
1.89 kV
Bending test turns
135
Conductor cross section tensile test
6 mm²
Short-time current
0.3 kA
Test spectrum
Service life test category 2, bogie-mounted
Test directions
X-, Y- and Z-axis (pos. and neg.)
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Connection method
Screw connection
Stripping length
9 mm
Conductor cross section flexible min.
0.14 mm²
2 conductors with same cross section, solid max.
1.5 mm²
Internal cylindrical gage
A4
Permissible humidity (storage/transport)
30 % ... 70 %
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 7.0
27141126
ECLASS 9.0
27141126
UNSPSC 6.01
30211811
UNSPSC 19.0
39121410
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Acceleration
30g
Shock duration
18 ms
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Length
57.8 mm
Height NS 35/15
55 mm
Tightening torque max
0.8 Nm
Conductor cross section AWG min.
26
Conductor cross section flexible, with ferrule without plastic sleeve max.
4 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, maximum
1.5 mm²
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 4.0
27141100
ECLASS 5.1
27141100
ETIM 7.0
EC000902
UNSPSC 7.0901
39121410
UNSPSC 20.0
39121410
Conductor cross section AWG max.
10
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.14 mm²
2 conductors with same cross section, solid min.
0.14 mm²
2 conductors with same cross section, stranded max.
1.5 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 11.0
27141126
ETIM 2.0
EC000902
UNSPSC 12.01
39121410
UNSPSC 21.0
39121410