2909885 Phoenix Contact Relays

2909885 Product Details

• Type of note
  Notes on operation
• Height
  93 mm
• Degree of protection
  IP20 (Relay base)
• Typical input current at UN
  18 mA
• Utilization restriction
  EMC: class A product, see manufacturer's declaration in the download area
• Depth
  75 mm
• Maximum altitude
  ≤ 2000 m
• Input voltage range in reference to UN
  see diagram
• Coil voltage
  24 V DC
• Type of switch contact
  Single contact
• Limiting continuous current
  6 A
• Operating mode
  100% operating factor
• Connection method
  Screw connection
• Stripping length
  8 mm
• Conductor cross section flexible (2 conductors with same cross section)
  0.5 mm² ... 2.5 mm²
• Rated insulation voltage
  250 V AC
• Pollution degree
  2
• China RoHS
  Environmentally Friendly Use Period = 50 years
• ECLASS 6.0
  27371600
• ETIM 2.0
  EC001437
ETIM 6.0
EC001437
Width
16 mm
Ambient temperature (operation)
-40 °C ... 70 °C
Typical release time
10 ms
Protective circuit
Free-wheeling diode Damping diode
Maximum switching voltage
250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Maximum inrush current
80 A (for 20 ms)
Switching capacity
2 A (at 24 V, DC13)
Mechanical service life
3x 107 cycles
Conductor cross-section solid (2 conductors with same cross section)
0.5 mm² ... 2.5 mm²
Conductor cross section AWG
20 ... 10 (solid)
Standards/regulations
EN 50178
Insulation
Safe isolation, reinforced insulation
ECLASS 10.0.1
27371601
ECLASS 7.0
27371601
ETIM 7.0
EC001437
Contact material
AgSnO
Switching capacity min.
1200 mW
Interrupting rating (ohmic load) max.
264 W (at 24 V DC, observe contact derating)
Connection name
Contact side
Assembly instructions
In rows with zero spacing
Conductor cross section flexible
0.5 mm² ... 4 mm²
Designation
Corrosive gas test
Identification
ISA-S71.04. G3 Harsh Group
ECLASS 11.0
27371601
ECLASS 5.0
27371600
ETIM 3.0
EC001437
Note
FBS 2-6... plug-in bridge for the input side (A2) and FBS-2-8... plug-in bridge for the output side (11/21)
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Nominal input voltage UN
24 V DC
Typical response time
8 ms
Operating voltage display
Yellow LED
Power dissipation for nominal condition
0.43 W
Contact type
1 N/O contact
Minimum switching voltage
12 V AC/DC (at 100 mA)
Min. switching current
100 mA (at 12 V DC)
Test voltage
4 kV AC (50 Hz, 1 min., winding/contact)
Mounting position
any
Conductor cross section solid
0.5 mm² ... 4 mm²
Torque
0.5 Nm ... 0.6 Nm
Rated surge voltage
6 kV
Overvoltage category
III
ECLASS 5.1
27371600
ECLASS 9.0
27371601
ETIM 4.0
EC001437

Product condition