2903352 Phoenix Contact Relays

2903352 Product Details

• Type of note
  Notes on operation
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Nominal input voltage UN
  120 V AC
• Typical release time range
  3 ms ... 20 ms
• Maximum inrush current
  50 mA
• Switching capacity
  2 A (at 24 V, DC13)
• Connection name
  Contact side
• Conductor cross section solid
  0.5 mm² ... 4 mm²
• Torque
  0.5 Nm ... 0.6 Nm
• Height
  89 mm
• Ambient temperature (operation)
  -40 °C ... 50 °C
• Typical input current at UN
  8 mA
• Operating voltage display
  Yellow LED
• Maximum switching voltage
  250 V AC/DC
• Limiting continuous current
  25 A (20 ms, N/O contacts)
• Mechanical service life
  approx. 107 cycles
• Stripping length
  8 mm
• Conductor cross section flexible
  0.5 mm² ... 4 mm²
• Pollution degree
  2
• China RoHS
  Environmentally Friendly Use Period = 50 years
ECLASS 9.0
27371601
UNSPSC 6.01
30211917
UNSPSC 13.2
39122334
Utilization restriction
EMC: class A product, see manufacturer's declaration in the download area
Depth
75 mm
Mains frequency
50/60 Hz
Type of switch contact
Single contact
Min. switching current
10 mA (at 12 V)
Service life, electrical
see diagram
Mounting position
any
Conductor cross section flexible (2 conductors with same cross section)
0.5 mm² ... 2.5 mm²
Rated insulation voltage
250 V AC
Insulation
safe isolation
Identification
ISA-S71.04. G3 Harsh Group
ECLASS 5.0
27371600
ETIM 4.0
EC001437
ETIM 7.0
EC001437
UNSPSC 19.0
39122334
Note
the following values are applicable if a gold layer is destroyed
Input voltage range in reference to UN
see diagram
Coil voltage
120 V AC
Minimum switching voltage
12 V (at 10 mA)
Test voltage
4 kVrms (50 Hz, 1 min., winding/contact)
Flammability rating according to UL 94
V2 (Housing)
Connection method
Screw connection
Conductor cross section AWG
20 ... 10 (solid)
Rated surge voltage
6 kV
ECLASS 10.0.1
27371601
ECLASS 5.1
27371600
ETIM 3.0
EC001437
UNSPSC 7.0901
39121516
UNSPSC 12.01
39121516
Width
16 mm
Degree of protection
IP20 (Relay base)
Typical response time
3 ms ... 12 ms
Protective circuit
Varistor
Contact type
1 changeover contact
Contact material
AgNi
Interrupting rating (ohmic load) max.
240 W (at 24 V DC)
Operating mode
100% operating factor
Assembly instructions
In rows with zero spacing
Conductor cross-section solid (2 conductors with same cross section)
0.5 mm² ... 2.5 mm²
Standards/regulations
DIN EN 50178
Designation
Corrosive gas test
ECLASS 11.0
27371601
ECLASS 4.0
27371100
ECLASS 7.0
27371601
ETIM 6.0
EC001437
UNSPSC 18.0
39122334
UNSPSC 20.0
39122334
Overvoltage category
III
ECLASS 4.1
27371100
ECLASS 6.0
27371600
ETIM 2.0
EC001437
UNSPSC 11
39121516
UNSPSC 21.0
39122334

Product condition