2903157 Phoenix Contact AC/DC Power Supplies

2903157 Product Details

• Degree of protection
  IP20
• Degree of pollution
  2
• Nominal power consumption
  137.3 VA
• Type of protection
  Transient surge protection
• Connection in parallel
  Yes, for redundancy and increased capacity
• Power loss nominal load max.
  < 10 W (230 V)
• Housing material
  PC
• Conductor cross section flexible max.
  1.5 mm²
• UL approvals
  UL Listed UL 508
• Electromagnetic HF field
  EN 61000-4-3
• Surge voltage load (surge)
  EN 61000-4-5
• Criterion B
  Temporary impairment to operational behavior that is corrected by the device itself.
• ECLASS 11.0
  27040701
• ECLASS 10.0.1
  27040701
• ECLASS 6.0
  27049000
• ETIM 4.0
  EC002540
• ECLASS 9.0
  27040701
• UNSPSC 21.0
  39121004
• Depth
  115 mm
• Inflammability class in acc. with UL 94 (housing / terminal blocks)
  V0
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Dielectric strength maximum
≤ 300 V AC 15 s
Current consumption
1.1 A (100 V AC)
Recommended breaker for input protection
6 A ... 16 A (Characteristics B, C, D, K)
Setting range of the output voltage (USet)
12 V DC ... 18 V DC (> 12 V DC, constant capacity restricted)
Feedback voltage resistance
< 25 V
Output power
60 W
Efficiency
> 86 % (for 230 V AC and nominal values)
Mounting position
horizontal DIN rail NS 35, EN 60715
Conductor cross section solid max.
1.5 mm²
EMC requirements for noise immunity
EN 61000-6-1
Standard - Electrical safety
IEC 60950-1/VDE 0805 (SELV)
Rail applications
EN 50121-4
Discharge in air
8 kV (Test Level 3)
Test field strength
10 V/m (Test Level 3)
Fast transients (burst)
EN 61000-4-4
Height
130 mm
Installation distance top/bottom
50 mm / 50 mm
Ambient temperature (start-up type tested)
-25 °C
Climatic class
3K3 (in acc. with EN 60721)
Input voltage range
100 V AC ... 240 V AC -15 % ... +10 %
Discharge current to PE
< 0.25 mA
Mains buffering time
typ. 20 ms (120 V AC)
Power factor (cos phi)
0.51
Nominal output current (IN)
5 A
Connection in series
yes
Width
30 mm
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Nominal input voltage range
100 V AC ... 240 V AC
Inrush current
≤ 25 A (typical)
Protective circuit/component
Varistor
Protection against overvoltage at the output (OVP)
≤ 22 V DC
Net weight
0.32 kg
Assembly instructions
alignable: horizontally 0 mm (≤ 40 °C) 10 mm (≤ 70 °C), vertically 50 mm
Conductor cross section AWG max.
16
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Comments
Criterion A
Conducted interference
EN 61000-4-6
REACh SVHC
Lead 7439-92-1
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 4.0
27040702
ECLASS 5.1
27049002
ETIM 7.0
EC002540
UNSPSC 13.2
39121004
UNSPSC 19.0
39121004
Installation distance right/left
0 mm / 0 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Installation height
≤ 5000 m (> 2000 m, Derating: 10 %/1000 m)
AC frequency range
50 Hz ... 60 Hz ±10 %
Input fuse
6.3 A Slow-blow
Nominal output voltage
12 V DC ±1 %
Derating
> 60 °C ... 70 °C (2.5%/K)
Residual ripple
< 50 mVPP (with nominal values)
Maximum power dissipation in no-load condition
< 1 W (230 V)
Insulation voltage input/output
3 kV AC (type test)
Conductor cross section solid min.
0.2 mm²
Conductor cross section AWG min.
24
EMC requirements for noise emission
EN 61000-6-3
Standard – Safety extra-low voltage
IEC 60950-1 (SELV) and EN 60204-1 (PELV)
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Contact discharge
6 kV (Test Level 3)
Input
3 kV (Test Level 4 - symmetrical)
Signal
1 kV (Test Level 2 - asymmetrical)
Voltage dips
EN 61000-4-11
Frequency
50 Hz
ECLASS 5.0
27049002
ECLASS 4.1
27040702
ECLASS 7.0
27049002
ETIM 6.0
EC002540
UNSPSC 18.0
39121004
UNSPSC 20.0
39121004
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Typical response time
< 1 s
MTBF (IEC 61709, SN 29500)
25 °C
Protection class
II (in closed control cabinet)
Connection method
Push-in connection
Conductor cross section flexible min.
0.2 mm²
Stripping length
8 mm
Standard - Safety of transformers
EN 61558-2-16 (air clearances and creepage distances only)
Standard - Safe isolation
DIN VDE 0100-410
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Electrostatic discharge
EN 61000-4-2
Frequency range
0.15 MHz ... 80 MHz
Output
1 kV (Test Level 3 - symmetrical)
Voltage
230 V AC
Criterion A
Normal operating behavior within the specified limits.

Product condition