2902053 Phoenix Contact Electrical Measuring & Monitoring Instruments

2902053 Product Details

• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Configurable/programmable
  Yes
• Load/output load voltage output
  ≥ 10 kΩ
• Width
  6.2 mm
• Permissible humidity (operation)
  5 % ... 95 % (non-condensing)
• Sensor types that can be used (TC)
  B, C, E, J, K, N, R, S, T, L, U, A-1, A-2, A-3, M, L
• Number of outputs
  1
• Max. output current
  24.6 mA
• Load/output load current output
  ≤ 600 Ω (at 20 mA)
• Connection method
  Screw connection
• Stripping length
  10 mm
• Torque
  0.5 Nm ... 0.6 Nm
• Height
  109.81 mm
• Degree of protection
  IP20 (not assessed by UL)
• Screw thread
  M3
• Max. output voltage
  approx. 12.3 V
• Depth
  119.2 mm
• Supply voltage range
  9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715))
• Protective circuit
  Transient protection
• Rated insulation voltage
  300 V (effective)
Electromagnetic compatibility
Conformance with EMC directive
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 2
Standards/regulations
EN 61000-4-6
Typical deviation from the measuring range final value
0.05 %
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 11.0
27210129
ECLASS 4.1
27200200
ECLASS 6.0
27200200
ECLASS 9.0
27210129
ETIM 3.0
EC001446
ETIM 6.0
EC002919
Noise immunity
EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
Ripple
< 10 mVrms
Conductor cross section flexible
0.14 mm² ... 2.5 mm²
Degree of pollution
2
Noise emission
EN 61000-6-4
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 2
UL, USA/Canada
UL 508 Listed
Identification
C, EMC2
REACh SVHC
Lead 7439-92-1
ECLASS 4.0
27200200
ECLASS 5.0
27200200
ETIM 2.0
EC001446
UNSPSC 6.01
30211506
UNSPSC 12.01
39121008
UNSPSC 18.0
41112105
UNSPSC 20.0
41112105
UNSPSC 19.0
41112105
UNSPSC 13.2
41112105
Mounting position
any
ECLASS 10.0.1
27210129
ETIM 4.0
EC001446
UNSPSC 21.0
41112105
ATEX
 II 3 G Ex nA IIC T4 Gc X
ECLASS 5.1
27200200
ETIM 7.0
EC002919
UNSPSC 7.0901
39121008
Certificate
DNV GL 14445-15HH
ECLASS 7.0
27200206
UNSPSC 11
39121008
Conformance
CE-compliant
Conductor cross section solid
0.2 mm² ... 1.5 mm² (with ferrule)
Maximum temperature coefficient
≤ 0.01 %/K
Overvoltage category
II
Housing material
PBT
Current output signal
0 mA ... 20 mA (via DIP switch)
Conductor cross section AWG
24 ... 12 (flexible)
Typical cold point errors
2 K (2 K + (0,2 K * ΔT))
Assembly instructions
The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715.
Utilization restriction
EMC: class A product, see manufacturer's declaration in the download area
Short-circuit current
< 31.5 mA
Typical current consumption
32.7 mA (24 V DC)
Transmission error thermocouples
0.1% * 600 K / set measuring range; 0.1% > 600 K (C, E, J, K, N, T, L, U, M Gost, L Gost)
Test voltage, input/output/supply
3 kV (50 Hz, 1 min.)
Designation
Shipbuilding approval
Ambient temperature (operation)
-40 °C ... 70 °C
Temperature measuring range
-250 °C ... 2500 °C (Range depends on sensor type, range can be set freely via software or in increments from -150°C to 1350°C via DIP switches)
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 2
Voltage output signal
0 V ... 5 V (via DIP switch)
Power consumption
≤ 850 mW (at IOUT = 20 mA, 9.6 V DC, 600 Ω load)
Electrical isolation
Reinforced insulation in accordance with IEC 61010-1

Product condition