1288395 Phoenix Contact Electrical Wires & Cables

1288395 Product Details

• Application
  For charging with alternating current (AC) and with direct current (DC)
• Note on the connection method
  Crimp connection, cannot be disconnected
• Bore dimensions
  117.65 mm x 90 mm, 117.65 mm x 83 mm
• Conductor length
  2 m (AC cables)
• Type of charging current
  DC, AC 3-phase
• Type of signal transmission
  Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
• Insertion/withdrawal cycles
  > 10000
• Restrictions to mounting position
  Only 0 to 90 degree frontal inclination possible, see figure
• Customer variations
  On request
• External cable diameter
  1.6 mm -0.2 mm
• External sheath, color
  Green-yellow
• Typical motor current for locking
  0.25 A
• Service life insertion cycles
  > 10000 load cycles
• Mechanical emergency release
  available
• Tolerance at the sensor with the recommended measured current
  ±5K
• ECLASS 11.0
  27144706
• Design
  Generation 4
• Charging mode
  Mode 2, 3, 4
• Ambient temperature (operation)
  -40 °C ... 80 °C
• Maximum charging power
  200 kW
Rated voltage for power contacts
480 V AC
Insulation resistance of neighboring contacts
> 200 MΩ
Insertion force
< 100 N
Mounting hole diameter
6.80 mm (ø)
Flammability rating
V0
Locking type
Locking in the inserted state with a locking mechanism
Single wire, color
black PP/CS
Maximum voltage for locking detection
12 V
Recommended adaptation time
600 ms
Lock recognition
available
Resistance range
650 Ω ... 1450 Ω
Type
Locking actuator, left
Note
A protective cap is supplied as standard for the DC and AC contacts.
Width
108 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Number of power contacts
7 (L1, L2, L3, N, PE, DC+, DC-)
Rated current for signal contacts
2 A
Withdrawal force
< 100 N
Design line
Generation 4
Material surface of contacts
Ag
Outer sheath, material
PVC
Cable weight
7 kg/km
Operating voltage
12 V (Typical power supply at the motor)
Max. dwell time with reverse current
1 s
Standards/regulations
DIN EN 60751
Charging standard
CCS type 2
Depth
128.4 mm
Number of phases
3
Rated voltage for signal contacts
30 V AC
Temperature monitoring
AC contacts: PTC chain (DIN˽EN˽60738-1)
Mounting position of the locking actuator
Left-side
Screws included in the scope of delivery
none
Material
Plastic
Cable structure
4 x 0.5 mm²
Number of positions of theconnectors
4
Reverse current of the motor
max. 1.5 A
Cable length
1 m
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
ECLASS 10.0.1
27144706
Height
140.25 mm
Max. altitude
4000 m (above sea level)
Rated current of power contacts
32 A AC
Number of signal contacts
2 (CP, PP)
Resistor coding
4.7 kΩ (between PE and PP)
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Required mounting screws
M6
Housing color
black
Cable resistance
≤ 37.1 Ω/km
Minimum bending radius
15 mm
Possible power supply range at the motor
9 V ... 16 V
Pause time after entry or exit path
3 s
Type of sensor
Pt 1000
Temperature range
-40 °C ... 130 °C

Product condition