1270297 Phoenix Contact Electrical Wires & Cables

1270297 Product Details

• Charging mode
  Mode 2, 3, 4
• Depth
  128.4 mm
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Maximum charging power
  125 kW
• Rated current for signal contacts
  2 A
• Resistor coding
  4.7 kΩ (between PE and PP)
• Type
  Locking actuator right
• Note
  A protective cap is supplied as standard for the DC and AC contacts.
• Ambient temperature (operation)
  -40 °C ... 80 °C
• Design
  Generation 4
• Charging standard
  CCS type 2
• Height
  140.25 mm
• Conductor length
  2 m (AC cables)
• Number of phases
  1
• Number of power contacts
  5 (L1, N, PE, DC+, DC-)
• Temperature measurement
  DC contacts: Pt 1000 (DIN EN 60751)
• Mounting position of the locking actuator
  Right-side
• Required mounting screws
  M6
• Locking type
  Locking in the inserted state with a locking mechanism
• Outer sheath, material
  PVC
Number of positions of theconnectors
4
Max. dwell time with reverse current
1 s
Cable length
1 m
Type of sensor
Pt 1000
Resistance range
650 Ω ... 1450 Ω
Standards/regulations
DIN EN 60751
Width
108 mm
Max. altitude
4000 m (above sea level)
Type of charging current
DC, AC 1-phase
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Insulation resistance of neighboring contacts
> 200 MΩ
Insertion/withdrawal cycles
> 10000
Design line
Generation 4
Flammability rating
V0
Cable structure
4 x 0.5 mm²
Single wire, color
black PP/CS
Recommended adaptation time
600 ms
Service life insertion cycles
> 10000 load cycles
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
ECLASS 11.0
27144706
Application
For charging with alternating current (AC) and with direct current (DC)
Note on the connection method
Crimp connection, cannot be disconnected
Bore dimensions
117.65 mm x 90 mm, 117.65 mm x 83 mm
Rated voltage for power contacts
250 V AC
Rated voltage for signal contacts
30 V AC
Temperature monitoring
AC contacts: PTC system (DIN EN 60738-1)
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Housing color
black
Material surface of contacts
Ag
Cable resistance
≤ 37.1 Ω/km
Minimum bending radius
15 mm
Typical motor current for locking
0.25 A
Mechanical emergency release
available
ECLASS 9.0
27144706
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Rated current of power contacts
32 A AC
Number of signal contacts
2 (CP, PP)
Insertion force
< 100 N
Withdrawal force
< 100 N
Customer variations
On request
External cable diameter
1.6 mm -0.2 mm
Cable weight
7 kg/km
Possible power supply range at the motor
9 V ... 16 V
Maximum voltage for locking detection
12 V
Pause time after entry or exit path
3 s
Temperature range
-40 °C ... 130 °C
Mounting hole diameter
6.80 mm (ø)
Screws included in the scope of delivery
none
Material
Plastic
External sheath, color
Green-yellow
Operating voltage
12 V (Typical power supply at the motor)
Reverse current of the motor
max. 1.5 A
Lock recognition
available
Tolerance at the sensor with the recommended measured current
±5K
ECLASS 10.0.1
27144706

Product condition