1211201 Phoenix Contact Electrical Wires & Cables

1211201 Product Details

• Design
  Generation 4
• Height
  140.25 mm
• Ambient temperature (operation)
  -30 °C ... 50 °C
• Type of charging current
  DC, AC 1-phase
• Type
  Locking actuator right
• Note
  A protective cap is supplied as standard for the DC and AC contacts.
• Width
  108 mm
• Degree of protection
  IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
• Max. altitude
  4000 m (above sea level)
• Insulation resistance of neighboring contacts
  > 200 MΩ
• Temperature monitoring
  AC contacts: PTC chain (DIN˽EN˽60738-1)
• Restrictions to mounting position
  Only 0 to 90 degree frontal inclination possible, see figure
• Screws included in the scope of delivery
  none
• External cable diameter
  1.6 mm -0.2 mm
• Cable structure
  4 x 0.5 mm²
• Standards/regulations
  DIN EN 60751
• Charging mode
  Mode 2, 3, 4
• Depth
  128.4 mm
• Number of phases
  1
• Number of power contacts
  5 (L1, N, PE, DC+, DC-)
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Mounting position of the locking actuator
Right-side
Housing color
black
Customer variations
On request
Cable weight
7 kg/km
Maximum voltage for locking detection
30 V
Service life insertion cycles
> 10000 load cycles
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
ECLASS 11.0
27144706
ECLASS 9.0
27144706
Application
For charging with alternating current (AC) and with direct current (DC)
Note on the connection method
Crimp connection, cannot be disconnected
Conductor length
2 m (AC cables)
Maximum charging power
125 kW
Rated current of power contacts
32 A AC
Rated current for signal contacts
2 A
Insertion force
< 100 N
Required mounting screws
M6
Material
Plastic
Locking type
Locking in the inserted state with a locking mechanism
External sheath, color
Green-yellow
Minimum bending radius
15 mm
Reverse current of the motor
max. 0.5 A
Recommended adaptation time
600 ms
Mechanical emergency release
available
Charging standard
CCS type 2
Bore dimensions
117.65 mm x 90 mm, 117.65 mm x 83 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Rated voltage for power contacts
250 V AC
Rated voltage for signal contacts
30 V AC
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Insertion/withdrawal cycles
> 10000
Design line
Generation 4
Flammability rating
V0
Outer sheath, material
PVC
Single wire, color
black PP/CS
Possible power supply range at the motor
22 V ... 26 V
Cable length
0.5 m
ECLASS 10.0.1
27144706
Number of signal contacts
2 (CP, PP)
Resistor coding
4.7 kΩ (between PE and PP)
Withdrawal force
< 100 N
Mounting hole diameter
6.80 mm (ø)
Material surface of contacts
Ag
Cable resistance
≤ 37.1 Ω/km
Number of positions of theconnectors
4
Typical motor current for locking
0.05 A
Pause time after entry or exit path
3 s
Lock recognition
available
Tolerance at the sensor with the recommended measured current
±5K
Operating voltage
24 V (Typical power supply at the motor)
Max. dwell time with reverse current
1 s
Type of sensor
Pt 1000
Resistance range
650 Ω ... 1450 Ω
Temperature range
-40 °C ... 130 °C

Product condition