8069730 Festo Pneumatic Components

8069730 Product Details

• Topologies
  Star Line
• Rotor position sensor measuring principle
  Magnetic
• Max. rotational speed
  3300 1/min
• Characteristics of digital logic outputs
  Freely configurable in some cases Not galvanically isolated
• Nominal current
  7.2 A
• Absolute encoder operating time
  With external battery: max. 6 months Note: the maximum service life of the battery depends its state of charge, the ambient temperature and ageing effects. Without external battery: 3 days (worst case) up to a maximum of 7 days (best case) Note: Maximum s
• Motor peak power
  200 W
• Note on ambient temperature
  Above an ambient temperature of 20 °C, the power must be reduced by 1.75% per °C.
• Permissible axial shaft load
  60 N
• Number of digital logic inputs
  2
• Work range of logic input
  24 V
• Ethernet, supported protocols
  TCP/IP
• Additional functions
  CoE (CSP only) Variable PDO mapping
• Type code
  EMCA
• Performance Level (PL)
  Safe torque off (STO)/category 3, performance level d
• Nominal rotary speed
  3150 1/min
• Max. positive test pulse with 0 signal
  10000 µs
• Parameterization interface
  Ethernet
• Permissible voltage fluctuations
  +/- 20 %
• Peak current
  10.3 A
Ambient temperature
0 °C ... 50 °C
Degree of protection
IP54
PFD
1.86E-5
Communication profile
CiA402 FHPP
KC characters
KC EMC
Configuration support
ESI file
Minimum cycle time
2 ms
Protective function
I²t monitoring Software end position detection
Safety function
Safe torque off (STO)
Braking resistor, external
6 Ohm
Max. current of digital logic outputs
100 mA
Protocol
EtherCAT
Max. number of positioning sets
64
Vibration resistance
Transport application test with severity level 2 as per FN 942017-4 and EN 60068-2-6
Storage temperature
-25 °C ... 70 °C
Rotor mass moment of inertia
0.301 kgcm²
Permissible radial shaft load
100 N
Proof test interval
20 y
Input switching logic
PNP (positive switching)
Rotor position sensor
Absolute encoder, single-turn
Display
LED
Diagnostic coverage
90 %
Max. negative test pulse on 1 signal
600 µs
DC nominal voltage
24 V
Certificate issuing authority
German Technical Control Board (TÜV) 01/205/5514.00/16 UL E331130
Shock resistance
Shock test with severity level 2 as per FN 942017-5 and EN 60068-2-27
Peak torque
0.91 Nm
PFH
1.0E-9
Product weight
2260 g
Switching logic at outputs
PNP (positive switching)
Media redundancy
Ring redundancy
Baud rate
10/100 Mbit/s (full/half)
Controller operating mode
PWM MOSFET power output stage PI current regulator
Safety integrity level (SIL)
Safe torque off (STO)/SIL 2
Hardware fault tolerance
1
Motor nominal power
150 W
SFF safe failure fraction
> 90 %
Rotor position sensor resolution
12 bit
CE marking (see declaration of conformity)
As per EU EMC directive as per EU machinery directive
Relative air humidity
0 - 95 % Non-condensing
Certification
RCM compliance mark c UL us - Recognized (OL)
Nominal torque
0.45 Nm
Number of digital logic outputs 24 V DC
2
Logic input specification
Based on IEC 61131-2
Characteristics of logic input
Galvanically connected to logic potential
Type of mounting
Screwed tightly With through-hole
Note on materials
Contains paint-wetting impairment substances RoHS-compliant

Product condition

Related documents 8069730 Specs